3/19/2024 0 Comments Orbit replacement sprinkler headI bought the HD version of the maxipaw, just because I needed to get my system up and running as we were getting a few days in the 90's and rachio told me it has to run. Hunter and rainbird are quality, they have their pro lines and consumer, but overall, I think they are likely better. Take a shovel to it and investigate.Īs for the quality of Orbit, I have no idea, but a ignorant assumption says they are the cheaper solution available at big box. If the zone if running poorly something is cracked and or broken. I would say you know it is leaking for sure if the water is puddling a lot while running. Dug it out, repaired and closed it up, now I just assume there is no leak. ![]() Turned out to be a cracked threaded pipe. The stem rises 1-3/4 inches above the sod level and conveniently drops into the riser when not in operation. The nozzle has an adjustable-flow screw and sprays a distance up to a 15 foot radius. I had a pop-up in my one zone that was not working well and in turn the rest were lacking too. The Orbit Brass Pop-Up Sprinkler features a gravity head made from solid brass and a brass half-pattern nozzle. Either way, the point is the ground is soft in the area and without running it when dug out, it is difficult to tell if it is leaking under ground. (he didnt know how to grow grass and had more dirt brought 3 times when it wasnt growing). It was 2" below grade because my insane neighbor thought it was his yard and buried it in top soil. As a result, the ground gets a little soupy in the area, but I hope that has something to do with me digging it up. I am likely going to replace one of the heads with a seal a matic one because the entire zone leaks out through one that is at the lowest point of the yard. It is very odd and has nothing to do with your issue, but I am mentioning it anyway. The maxipaw pops up out of a cup, so I would expect to see water in it. ![]() I know some of mine have water around them while running. For outdoor irrigation use with cold water only.If it is leaking at the base, dig it up, put some thread tape on the the threads and then tighten it down again. Recommended operating pressure is 60 PSI. The Voyager II replaces rotors from Orbit, Hydro-Rain, and other major brands. MPT Funny Pipe fittings, swing fittings and risers. male pipe thread (MPT) Blu-Lock combination swing joint, although it is compatible with 3/4-in. The state-of-the-art approach to mounting a Voyager II is on a 3/4-in. ![]() The can and riser stem are made from high impact ABS and metal components are made from stainless steel.Īdjustment of both the radius and arc requires the included gear-drive rotor key. It also includes a bottom inlet filter which helps prevent clogging of the nozzle. It includes a radius adjustment screw which allows you to reduce the rotor throw down to 75% of its rated distance. It also includes a matched-precipitation nozzle rack with 1.0, 2.0, 3.0, 4.0 standard and low-angle nozzles featuring a unique keyway design to ensure highly uniform close-in and far-out watering, as well as an 8.0 GPM pasture nozzle. This very low rate reduces the risk of runoff or puddling for many soil types and conditions. It comes with a pre-installed 3-gallon-per-minute (GPM) nozzle which results in a full-pattern precipitation rate of 0.24 in. pop-up height ensures that the nozzle clears tall grass. Its arc is adjustable from 40 to 360 degrees in precise increments, which gives you the ability to aim it so that the water hits the landscape only and avoids any hardscape surfaces. The Voyager II gear-drive rotor is engineered specifically to water landscape areas which require a throw distance of up to 35 ft.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |